How To Connect Trekz Air Headphones: Easy Pairing Guide

To connect Trekz Air headphones, turn on pairing mode, then select them in your device’s Bluetooth settings.

Learning how to connect Trekz Air headphones is simple once you know the correct button sequence. This guide explains the setup for phones, tablets, computers, and TVs, along with clear fixes for pairing errors, weak connections, and devices that will not reconnect.

What to know before connecting Trekz Air headphones

Trekz Air headphones are open-ear Bluetooth headphones made by AfterShokz, which is now known as Shokz. They send sound through bone conduction, so the ear canals stay open while you listen.

Before you begin, check these points:

• Charge the headphones with the included micro-USB cable.

• Keep the headphones within a few feet of your phone or other device.

• Turn off Bluetooth on nearby devices that may already be connected.

• Remove the headphones from their charging cable.

• Make sure your phone, tablet, computer, or TV supports Bluetooth audio.

Trekz Air headphones use Bluetooth pairing rather than a special app. That means you can connect them through the normal Bluetooth menu on most modern devices.

How to connect Trekz Air headphones to an iPhone or Android phone

The steps for how to connect Trekz Air headphones are nearly the same on iPhone and Android. The main difference is the location of the Bluetooth menu.

Put Trekz Air headphones into pairing mode

1. Start with the headphones turned off.

2. Press and hold the Volume+ button for about 5 to 7 seconds.

3. Keep holding the button until the LED flashes red and blue.

4. Listen for the voice prompt that says, “Pairing.”

The Volume+ button is on the control panel near the right side of the headphones. The multifunction button is usually located between the volume buttons.

Connect to an iPhone

1. Open the Settings app.

2. Tap Bluetooth.

3. Turn Bluetooth on if it is disabled.

4. Wait for “Trekz Air” or “AfterShokz Trekz Air” to appear under Other Devices.

5. Tap the headphone name.

6. Wait until the status changes to Connected.

Your iPhone may remember the headphones after the first setup. On later uses, turn on the headphones and keep Bluetooth enabled. They should connect automatically if no other device takes priority.

Connect to an Android phone

1. Open Settings.

2. Tap Connected devices, Connections, or Bluetooth. The wording can vary by Android brand.

3. Turn Bluetooth on.

4. Tap Pair new device if that option appears.

5. Select Trekz Air from the list.

6. Confirm the pairing request if your phone displays one.

If the headphones do not appear, turn Bluetooth off and on again. Then place the headphones back into pairing mode instead of simply turning them on.

How to connect Trekz Air headphones to a Windows PC

You can connect Trekz Air headphones to a Windows computer for music, video calls, and system audio. Windows may show more than one sound device after pairing, so selecting the right output is important.

Pair with Windows 10 or Windows 11

1. Turn off the Trekz Air headphones.

2. Hold the Volume+ button for 5 to 7 seconds.

3. Release it when the LED flashes red and blue and the voice prompt says, “Pairing.”

4. On your computer, open Settings.

5. Select Bluetooth & devices.

6. Turn Bluetooth on.

7. Select Add device.

8. Choose Bluetooth.

9. Click Trekz Air when it appears.

10. Select Done after the connection finishes.

Now test the sound. Click the speaker icon in the Windows taskbar and choose Trekz Air as the output device.

For calls, Windows may list a headset or hands-free option. The hands-free profile supports the microphone but may reduce sound quality. For music, choose the stereo option when available.

If Windows connects but plays no sound

Open the sound settings and check the output device. A computer may remain connected to built-in speakers, a monitor, or another Bluetooth headset.

Also check the application itself. Video meeting apps often have their own speaker and microphone settings. Select Trekz Air inside the app if Windows alone does not route the call correctly.

How to connect Trekz Air headphones to a Mac

The process for how to connect Trekz Air headphones to a Mac takes less than a minute when the headphones are in pairing mode.

1. Turn off the headphones.

2. Hold Volume+ until the LED flashes red and blue.

3. Open the Apple menu on your Mac.

4. Select System Settings or System Preferences.

5. Choose Bluetooth.

6. Find Trekz Air in the device list.

7. Click Connect.

After pairing, open System Settings, select Sound, and choose Trekz Air under Output. If you plan to use the headphones for calls, select them under Input as well.

Older Macs may show a Bluetooth icon in the menu bar. You can use that menu to connect after the first pairing.

A useful tip is to remove old or unused Bluetooth devices from the Mac. A crowded device list does not always cause a problem, but it can make the correct device harder to find.

How to connect Trekz Air headphones to a TV

Many newer smart TVs support Bluetooth headphones. However, some TVs only support Bluetooth keyboards, remotes, or controllers. Check your TV manual if Trekz Air does not appear.

General TV pairing steps

1. Put Trekz Air into pairing mode.

2. Open the TV’s Settings menu.

3. Look for Sound, Audio, Bluetooth, or Speakers.

4. Select Bluetooth Audio or Add Device.

5. Choose Trekz Air from the list.

6. Confirm the connection.

The menu names differ by brand. On some televisions, you may need to open the sound output menu before searching for Bluetooth devices.

TV audio can have a delay. This happens when the TV processes the picture and sound at different speeds. If your TV has an audio sync setting, adjust it until voices match the picture.

Some TVs disconnect Bluetooth headphones when another audio device is selected. If that happens, choose Bluetooth headphones as the active sound output each time you use them.

How to connect Trekz Air headphones to a second device

Trekz Air headphones can support multipoint pairing, which allows them to remember more than one device. This feature is useful if you switch between a phone and a computer.

The pairing process for a second device can vary by firmware and model version. Use this general method:

1. Connect the headphones to the first device.

2. Turn the headphones off.

3. Place them into pairing mode by holding Volume+ for 5 to 7 seconds.

4. Pair them with the second device.

5. Turn the headphones off and on again.

The headphones may reconnect to both remembered devices, but they usually play audio from only one source at a time. If audio starts on the wrong device, pause playback on the first device or disconnect it temporarily.

In setup testing and troubleshooting, the most common mistake is trying to pair the second device while the first device is actively playing audio. Stop music and close calls before beginning a new pairing attempt.

How to reconnect Trekz Air headphones automatically

Once you finish how to connect Trekz Air headphones for the first time, future connections should be automatic. Turn on Bluetooth on the source device, then power on the headphones.

The headphones usually reconnect to the last compatible device. If several devices are nearby, they may connect to the wrong one or fail to connect because another device has control.

Try these steps:

• Turn off Bluetooth on devices you are not using.

• Turn the Trekz Air headphones off and on.

• Keep the source device close to the headphones.

• Open the Bluetooth menu and tap Trekz Air manually.

• Charge the headphones if the battery is low.

Automatic reconnection is convenient, but it is not guaranteed in every situation. Operating system updates, saved Bluetooth profiles, and nearby devices can change the connection behavior.

How to fix Trekz Air headphones that will not pair

If the normal steps fail, do not keep tapping the device name repeatedly. Start with a clean connection.

Forget the old Bluetooth connection

On your phone or computer, open the Bluetooth settings. Tap or click Trekz Air, then choose Forget, Remove, or Remove device.

Next, restart Bluetooth and place the headphones into pairing mode again. This creates a fresh Bluetooth profile instead of reusing a damaged or incomplete one.

Reset the headphones

A reset can help when the headphones connect to one device but refuse to connect to another. The commonly used reset sequence is:

1. Turn off the Trekz Air headphones.

2. Press and hold the multifunction button, Volume+, and Volume− at the same time.

3. Hold the buttons for about 3 seconds.

4. Release the buttons after the headphones respond.

The exact reset behavior can differ by firmware. If this sequence does not work, check the product manual for your specific Trekz Air version.

After the reset, repeat the full pairing process. The headphones may no longer remember earlier devices.

Check for interference

Bluetooth signals can weaken near crowded wireless areas. Wi-Fi routers, USB 3.0 devices, metal objects, and other Bluetooth products may contribute to dropouts.

Move the headphones and source device closer together. Also avoid placing the phone inside a bag or behind a thick wall during the first pairing attempt.

Confirm the battery

A very low battery can cause pairing failures, sudden shutdowns, or repeated disconnections. Charge the headphones for a while before trying again.

The Trekz Air model is older than many current Shokz products, so battery capacity may have declined with age. Lithium-ion batteries naturally lose capacity after repeated charge cycles.

Common Trekz Air connection problems

The headphones do not appear in Bluetooth settings

Make sure the LED is flashing red and blue. A slow blue flash usually means the headphones are powered on, not necessarily in pairing mode.

Turn off nearby devices that may already know the headphones. Then restart pairing mode and search again.

Trekz Air connects but has no sound

Check the audio output setting on your device. The connection can be active while sound still comes from the phone speaker, computer speakers, or TV.

On a phone, raise the media volume rather than only the call volume. On a computer, choose Trekz Air from the sound output list.

The sound cuts out

Keep the source device within the normal Bluetooth range. Your body, walls, and other wireless devices can reduce signal strength.

If dropouts continue, forget the headphones, reset them, and pair them again. Also test with a different phone to see whether the problem follows the headphones or the original device.

The microphone does not work

Open the call or meeting app settings and select Trekz Air as the microphone. Bluetooth headphones can have separate output and input selections.

On Windows, confirm that the app has permission to use the microphone. On iPhone and Android, check the app’s microphone permission in system settings.

Only one side seems to work

Trekz Air uses a single open-ear band, so sound should come from the transducers on both sides. If one side is silent, check the audio balance settings on your device.

An extreme left or right balance can make one side seem broken. Hardware damage, moisture, or an aging cable can also cause this issue.

Tips for a stable Trekz Air Bluetooth connection

Good pairing habits prevent many connection problems. Think of Bluetooth like a short conversation: the devices need to be close, awake, and listening to each other.

Use these practical tips:

• Pair the headphones near the device you will use most.

• Keep the headphones charged.

• Do not pair them while they are connected to a charger.

• Pause music before switching between devices.

• Remove duplicate Trekz Air entries from old device lists.

• Restart both devices after a major operating system update.

• Keep the headphones dry and clean.

• Avoid bending or twisting the neckband.

• Use the correct audio output and microphone settings.

The Trekz Air design leaves your ears open, which helps you hear traffic, coworkers, or people nearby. That is a benefit for outdoor awareness, but it also means loud surroundings can compete with your audio. In a busy street or gym, the sound may seem quieter than it does in a calm room.

Frequently asked questions about how to connect Trekz Air headphones

How do I put Trekz Air headphones into pairing mode?

Turn the headphones off, then press and hold the Volume+ button for about 5 to 7 seconds. Release it when the LED flashes red and blue and the headphones say, “Pairing.”

Why are my Trekz Air headphones not showing up on my phone?

They may not be in pairing mode, or they may still be connected to another nearby device. Forget the old Bluetooth entry, turn off Bluetooth on nearby devices, and repeat the pairing process.

Can I connect Trekz Air headphones to two devices?

Trekz Air can support multipoint pairing in compatible setups, allowing it to remember more than one device. Audio normally comes from one active source at a time, so you may need to pause or disconnect the first device.

How do I reset Trekz Air headphones?

Turn the headphones off, then hold the multifunction button, Volume+, and Volume− together for about 3 seconds. After the reset, pair the headphones again through your device’s Bluetooth menu.

Why do Trekz Air headphones connect but play no audio?

Your device may still be using its built-in speakers or another output. Open the sound settings and select Trekz Air as the media or audio output.

Can Trekz Air headphones connect to a smart TV?

Yes, they can connect to a TV that supports Bluetooth audio. Open the TV’s sound or Bluetooth settings, place the headphones in pairing mode, and select Trekz Air.

Conclusion

The key to how to connect Trekz Air headphones is putting them into pairing mode before searching for them. Hold Volume+ until the red and blue lights flash, then select Trekz Air in your phone, computer, or TV Bluetooth menu.

If pairing fails, forget the old connection, reduce nearby wireless activity, charge the headphones, and reset them when needed. Follow these steps, test the sound output, and your Trekz Air headphones should be ready for calls, music, and everyday listening. Explore your device’s Bluetooth settings today, and share your experience if you discover another useful pairing tip.